Revive Your Ride: The Ultimate Guide to Restoring ATV Batteries - by Ranjeet Singh - CollectLo

Revive Your Ride: The Ultimate Guide to Restoring ATV Batteries

Ranjeet Singh - CollectLo

Ranjeet Singh

Content Writer

3 min read . Aug 26

Clap
Save

How to Restore ATV Batteries? 

Maintaining and caring for your All Terrain Vehicle (ATV) is one of the joyful procedures. Some individuals might find it overwhelming and a little daunting. But it can be a delightful part of your recreational routine when you possess a little knowledge. If finding the right battery for your ATV is key, then knowing the right method to restore it is crucial too. In this dedicated guide, readers will learn how to restore the battery for ATVs. It will certainly be helpful to enhance your recreational experience and adventure.

Various Types of ATV Batteries

ATVs or All Terrain Vehicles do use power sport batteries. These integrations can be found in personal watercraft, motorcycles, snowmobiles as well as other recreational vehicles. Primarily, you’ll find three types of power sport batteries for your ATVs –

Ø  Flooded Lead Acid

Ø  AGM (Absorbed Glass Mat)

Ø  Lithium-Ion Phosphate

Flooded lead acid batteries are the most common and affordable ATV batteries. However, they relatively come with shorter life spans than other counterparts. You do need to extend additional maintenance for these units since these batteries lose water during recharging because they aren’t completely sealed.

An AGM battery is more expensive but lasts more than flooded lead acid batteries. These batteries require less maintenance due to an absolute seal. These are quick to charge. Moreover, lithium-ion phosphate batteries are the most expensive batteries of all types. They do come with a whopping 3-year warranty and the lowest self-discharge rate.

How to Restore ATV Batteries? Various Methods Explained

ATV batteries are tough to regain their charging state once they are left to discharge. If they do so, they are unlikely to perform at the level they used to. Meanwhile, extreme cold or heat are critically hazardous factors as well for your battery’s health.

So, what is the ideal method to improve and maintain your ATV’s battery health? Well, you can prefer using a trickle or smart charger to attain the desired level of performance of your ATV’s battery. Both sorts of chargers can monitor your ATV battery and prevent discharging and maintain its health.

In another scenario, what is the option available to you when your ATV battery has died completely? Can you restore your ATV’s dead battery? Fortunately, the answer is YES. You can opt for a multi-mode smart charger to help your ATV battery survive again.

The following are some reputed ways you can consider to restore your ATV battery and make it work for you again:

Using a Standard Charger

It may happen when your ATV battery is completely discharged and your charger is unable to recognize if the battery is connected or not. Maybe the charger you are using would have been working in the past but not now. This is where you can trick your charger to start charging the dead battery. However, your charger must be able to deliver amps as low as 1-3.

To initiate the process, you do need to have a pair of jumper cables along with a charged battery. Further, you will connect the positive and negative terminals of both batteries using jumper cables. Now, start the charging process and then remove the cables from all terminals and wait for the dead battery to regain the energy.

Using a Smart Charger

Using a smart charger can also help you on this front. These types of chargers can detect the voltage intensity to perform accordingly. It proceeds in the secondary soft-start mode to recover the battery. Your smart charger will start powering the battery normally after switching to a Constant Current mode in case the soft-start mode is successful. On the contrary, it will display an error message to indicate replacing the battery.

Using a Desulfating Battery Charger

Sulfation is the key factor behind your ATV battery’s early failure. It continues to muster with the battery’s lifetime due to lead sulfate crystals. It forms more quickly when the battery is over/undercharged or left discharged for many days.

This is where smart chargers with desulfation attributes come to play. They break these crystals down in the battery plates by sending high-frequency electronic pulses through the battery. They do come with either a specific desulfation mode or perform desulfation during every charging process.